Updated November 2026
Whole house generator sizing comes down to one number: the total running watts your home needs, plus enough extra capacity to start the motors that pull the largest surge. This guide walks you through building a load list, calculating running and starting watts, adding a margin, and checking the result against standard generator sizes. Work through it once and you will know which size fits your house.
Step 1: List Every Load You Want Powered
Start with the circuits and appliances you actually need during an outage. Most homeowners cover the refrigerator and freezer, furnace or heat pump blower, well pump, sump pump, lighting, internet and modem, a few outlets, and sometimes an electric water heater or range. Check the nameplate on each appliance, which lists watts or amps at 120 or 240 volts. If only amps are listed, multiply amps by volts to get watts.
Shopping for one? See our guide: 4 Best Whole House Inverter Generator Options Compared (2026).
Step 2: Calculate Running and Starting Watts
Motors and compressors draw a surge when they start, often two to three times their running wattage for a moment. Refrigerators, well pumps, and central air compressors are the usual culprits. Add up the running watts of everything on your list, then identify the single largest starting surge. Your generator must handle the combined running load plus that one surge, because the other motors are normally already running or start at different times.
Step 3: Add a Safety Margin and Match a Generator Size
Many installers add roughly 20 percent to the total running load to leave headroom for future additions and to avoid running the unit at its absolute limit. Your final figure is the running load plus the largest surge, plus that margin. Compare it against standard generator ratings and choose the next size up if you land between two options. Keep in mind that generators are rated in kilowatts (kW) and that manufacturers publish both continuous and peak ratings. Use the continuous rating for your running calculation.
Sizing Example
The table below shows a simplified example. Your numbers will differ, so treat these values as placeholders for your own nameplate data.
| Load | Running Watts | Starting Surge Watts |
|---|---|---|
| Refrigerator | 700 | 2,100 |
| Furnace blower | 600 | 1,800 |
| Well pump (1/2 hp) | 1,000 | 3,000 |
| Lighting and electronics | 1,200 | 0 |
| Total running | 3,500 | |
| Largest surge (well pump) | 3,000 |
In this example the running load is 3,500 watts. Adding the largest surge brings the peak to about 6,500 watts, and a 20 percent margin on the running load raises the target to roughly 7,000 watts. That points toward a unit in the 7 to 8 kW range. For a wider look at larger units, see 22kw Whole House Generator: Sizing, Load Planning and Setup (2026).
Common Mistakes
- Sizing only for the refrigerator and lights and forgetting the well pump or sump pump surge.
- Using the peak rating instead of the continuous rating when comparing models.
- Ignoring future loads such as an EV charger, a window AC unit, or a heat pump upgrade.
- Skipping the transfer switch. The generator must be connected through a properly sized switch, and a planned backup setup is covered in Whole House Switch for Generator: How to Choose and Install One Safely.
- Assuming fuel type does not matter. Propane and natural gas units deliver different output, so confirm the rating for your fuel. See Whole House Generator LP Gas: Sizing, Setup and Key Steps (2026).
Recommended Gear
- Kill-A-Watt meter helps you measure actual wattage of plug-in appliances rather than relying only on labels. View on Amazon
- Clamp-on ammeter lets you read current on hardwired circuits and motors safely. View on Amazon
- Surge protector with a meter display can show live load on a circuit during testing. View on Amazon
FAQ
Do I need to size for the whole house or just essential circuits?
Most people size for essential circuits only, because a whole-home unit must cover the entire demand including central air and electric heat. Sizing for essentials usually produces a smaller, less expensive setup. Decide which loads matter before you calculate.
What happens if my generator is too small?
An undersized generator may trip its breaker, stall, or fail to start motors under load. Repeated overloads can shorten engine life. Choose the next size up if your calculation lands close to a rating limit.
Should I hire a professional to confirm the size?
Yes, an electrician or licensed installer should confirm your load calculation and wiring. Load calculations affect code compliance and safety, so consult a qualified professional before purchase or installation.
Conclusion
Good whole house generator sizing starts with an accurate list of loads, the running total, and the largest starting surge. Add a margin, compare against continuous ratings, and round up when you fall between sizes. Confirm the final choice with a licensed electrician before you buy.
