Updated November 2026
A 22kw whole house generator is a standby or dual-fuel unit rated to supply up to 22 kilowatts of electrical output, typically enough to run most of a single-family home during an outage. This guide shows you how to check whether that rating fits your home, how to add up your loads, and what to plan for installation and noise. The goal is a clear yes or no before you spend any money.
Step 1: Confirm Your Service Size and Voltage
Start with the main breaker on your electrical panel. Most US homes run on 120/240V split-phase service rated at 100A, 150A or 200A. A 22kw unit produces about 91.7 amps at 240V, so a 100A panel can be too small to take the generator through an automatic transfer switch without load limits. Confirm your service rating before you go further, and have a licensed electrician check the panel capacity.
Shopping for one? See our guide: 4 Best Whole House Inverter Generator Options Compared (2026).
Step 2: Calculate Your Essential Load
A whole house generator only needs to run the circuits you care about during an outage. Work through the loads in this order:
- List every appliance you want running, including the furnace or heat pump blower, well pump, refrigerator, freezer and sump pump.
- Check the nameplate wattage of each item. For motors, use the starting (locked-rotor) wattage, which can be three to six times the running wattage.
- Add the running loads, then add the largest single starting surge on top of them.
- Compare that total to the 22kW rating, keeping about 20 percent headroom for safety and future needs.
If your total stays under roughly 17 to 18kW of combined running load plus the largest surge, a 22kW unit has room to spare. If you have central air conditioning, an electric range and an electric water heater all running together, you may need load shedding or a smaller set of circuits.
Step 3: Choose Between Standby and Portable Setups
A 22kw whole house generator is almost always a permanently installed standby unit, fueled by natural gas, propane or a dual-fuel setup. It connects through an automatic transfer switch that starts the engine and moves the house loads over within seconds. Portable generators in this output range are rare and heavy, and wiring them into a home requires a manual transfer switch and careful backfeed prevention. Confirm which fuel supply your home can deliver at full load, since gas lines sized for a range and dryer may not meet a 22kW draw.
Step 4: Plan Placement and Noise Before Installation
Standby units are rated for noise at a set distance, and that rating changes significantly with placement. Position the unit away from bedroom windows, keep clearance for airflow and service access, and follow the clearance distances in the manufacturer’s installation manual. For practical steps on reducing sound at the property line, see Whole-House Generator Noise Reduction: 8 Steps That Actually Work. Understanding where noise comes from helps too: What Makes a Generator Loud: The Main Sources of Generator Noise explains the main sources.
Quick sizing reference
| Home setup | Typical 22kW fit |
|---|---|
| Electric heat, one central AC, gas range | Good fit with load management |
| All-electric, two AC units, electric range | Often too much load for 22kW without shedding |
| Gas heat, small electric load, well pump | Generous headroom |
Common Mistakes to Avoid
- Sizing from the appliance label alone and ignoring motor starting surge.
- Assuming the gas line can carry full output without a pressure check.
- Placing the unit under an overhang or near a window where exhaust can enter the home.
- Skipping the annual maintenance schedule, which keeps standby units starting reliably.
- Installing without a permit or a licensed electrician, which can affect insurance coverage.
Recommended Gear
A basic load meter helps you measure real draw on your circuits before you buy, not just the nameplate ratings.
- Clamp meter for measuring circuit current: lets you check actual running and starting amps on major appliances. View on Amazon
- Plug-in power monitor: records wattage on individual appliances over a few days of normal use. View on Amazon
FAQ
Can a 22kw whole house generator run central air conditioning?
Yes, usually, but central air is one of the largest starting loads in a home. Many owners pair the generator with soft-start kits or limit the AC to one unit during an outage.
Does a 22kw unit need a 200A service?
Not always, but many installations work best with a 200A panel. Your electrician can confirm whether your service and transfer switch can handle the full output.
How often should a standby generator be tested?
Manufacturers commonly recommend a weekly self-test and a periodic load test. Check the owner’s manual for the exact schedule for your model.
Conclusion
A 22kw whole house generator suits homes that want broad backup power, but only after you total the real starting and running loads. Check your service size, plan the fuel supply and placement, and confirm the installation with a licensed electrician. For current pricing, permits and installer details, consult local professionals and the manufacturer directly.
