Updated November 2026

A whole house generator sale can look like a bargain, but the unit only earns its keep if it matches your home’s electrical load, fuel supply and noise tolerance. This guide walks you through sizing the generator, comparing specifications, and checking the points that sales listings often leave out, so you can buy with confidence.

Step 1: Calculate Your Required Output

Start with your electrical load, not the sticker on the box. List the circuits you want to keep running during an outage, such as the furnace or heat pump blower, refrigerator, sump pump, well pump, lighting and a few outlets. Add the running watts of each item, then add the starting (surge) watts for motors, which can be several times higher. Most homeowners end up in the 10 kW to 22 kW range for full-home coverage, but your own list is the only reliable guide.

Shopping for one? See our guide: 4 Best Whole House Inverter Generator Options Compared (2026).

Step 2: Compare Fuel Type and Noise Data

Natural gas, propane (LP) and dual-fuel units each have trade-offs. Natural gas offers a continuous supply if your utility stays up, while propane lets you store fuel on site. Check the decibel rating the manufacturer publishes, and note the distance it was measured at, usually 23 feet. A unit rated near 60 dBA at that distance will sound far quieter at a neighbor’s property line than a rating taken at close range would suggest. For ways to lower the sound after installation, see Whole-House Generator Noise Reduction: 8 Steps That Actually Work.

Step 3: Verify Transfer and Monitoring Equipment

A generator needs a way to connect safely to your panel. Confirm whether the sale price includes an automatic transfer switch, or whether you will need to buy one separately. Review Whole House Switch for Generator: How to Choose and Install One Safely to understand what a compatible switch involves. Also check whether the warranty covers the engine, the controller and the alternator, and whether a licensed electrician must perform the installation to keep that warranty valid.

Step 4: Check the Seller and Total Setup Requirements

A low sale price rarely covers the full project. Ask whether the quote includes the concrete pad, gas line work, permits and inspection. Permitting rules differ by city and county, so confirm local requirements before you commit. Verify that the seller or installer is licensed and insured. For guidance on evaluating installers, read Whole House Generator Installer: How to Choose One Safely (2026).

Pre-Purchase Checklist

  1. Written list of loads to back up, with running and starting watts for each.
  2. Confirmed fuel source and supply pressure or tank capacity.
  3. Published dBA rating and the distance it was measured at.
  4. Transfer switch status: included, separate, or not required.
  5. Warranty terms, including any installer requirements.
  6. Itemized list of pad, gas line, permit and inspection work.

A surge protector designed for generator-fed circuits helps guard sensitive electronics against voltage spikes during transfer. View on Amazon

A digital multimeter lets you check voltage and continuity when you verify the transfer switch or test outlets after installation. View on Amazon

Common mistakes to avoid

  • Sizing to the average load instead of the surge load of motors.
  • Comparing a noise rating taken at a different distance.
  • Assuming the sale price covers the transfer switch, pad and permits.
  • Skipping a fuel supply check, especially for propane tank sizing.
  • Buying a unit before confirming local permit and HOA rules.

FAQ

Is a whole house generator sale worth it?

It can be, but only if the unit’s output, fuel type and included equipment match your home. Compare the full installed cost, not just the unit price.

What size whole house generator do I need?

Add the running and starting watts of every circuit you want to keep on, then choose a unit with enough capacity for the combined surge load. An electrician or licensed installer can verify the numbers against your panel.

Do I need a licensed electrician to install one?

In most areas, yes, and a permit is typically required. Check your local code and your warranty terms. Consult a licensed professional before any electrical or gas work.

Conclusion

A whole house generator sale is only a good deal when the unit fits your load, fuel supply and noise limits. Work through the sizing steps, compare the published noise data, and get a written list of everything the price includes. Confirm details with a licensed professional before you buy.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our generators & noise guides, checking product details against manufacturer specifications and owner feedback.