Updated November 2026

A whole house generator what size do I need question comes down to one number: the total wattage your home needs to run at the same time, plus a margin for motor starting surges. This guide walks you through listing your loads, adding them up correctly, and converting the result into a generator rating you can shop for. By the end, you will have a target kW figure you can take to an installer or a dealer.

Step 1: List the Loads You Want to Power

Start by deciding what you actually need during an outage. Most owners cover the furnace or heat pump, refrigerator, well pump or sump pump, lighting, internet gear, and a few outlets. Electric water heaters, electric ranges, central air conditioning, and EV chargers are the big draws, and they determine whether you end up with a mid-size or large unit.

Shopping for one? See our guide: What Size Generator to Power Whole House: 4 Best Picks for 2026.

Step 2: Find the Running and Starting Watts

Every appliance has two numbers. Running watts are what it draws continuously. Starting watts are the brief spike when a motor or compressor kicks on, which can be two to three times the running figure. Check the nameplate or manufacturer’s spec sheet for each device. Where the nameplate lists only amps, multiply amps by the voltage (120 or 240) to get watts.

Step 3: Calculate the Total and Add a Margin

Add the running watts of everything you plan to run at once. Then add the largest starting surge from any single motor, since that surge is the only one that typically overlaps the rest. Finally, add 20 to 25 percent of headroom so the generator is not running at its absolute limit. The result is your minimum generator capacity in kilowatts.

  1. Write down every load and its running watts.
  2. Note each motor’s starting watts.
  3. Sum the running watts of all loads you will use together.
  4. Add the single largest starting surge.
  5. Add 20 to 25 percent headroom and divide by 1,000 for kW.

Step 4: Choose Between Whole-Home and Partial-Home Coverage

Sizing for the entire house is more expensive to buy and install. Many homeowners instead use a load management approach, sizing the generator for essentials only. Your electrician can add a transfer switch that feeds selected circuits, which often lets you drop a size or two. For how the switching side works, see Whole House Switch for Generator: How to Choose and Install One Safely.

Quick Sizing Reference

Home Scope Typical Load Focus Common Rating Range
Essentials only Fridge, lights, furnace fan, router Roughly 7 to 12 kW
Mid-size home Essentials plus well pump and some AC Roughly 12 to 16 kW
Large home, full coverage Central AC, electric range, water heater Roughly 16 to 22 kW or more

These ranges are general. Your own calculation from Steps 1 through 3 should drive the final choice, and a licensed electrician should confirm it against your service panel.

Common Mistakes

  • Sizing from the appliance label instead of the actual running draw.
  • Ignoring starting surges from well pumps and AC compressors.
  • Skipping the 20 to 25 percent headroom.
  • Assuming a bigger unit is always better; oversized generators can run inefficiently at light loads.
  • Forgetting future additions such as an EV charger or heat pump.
  • A plug-in watt meter helps you measure real running draw of appliances rather than relying on labels alone. View on Amazon
  • A clamp meter lets you read current on individual circuits during testing. View on Amazon
  • A basic load calculation worksheet keeps your running and starting figures organized before you call a dealer. View on Amazon

FAQ

Can I size a whole house generator from my electric bill?

Not reliably. A bill shows average monthly energy use, not peak simultaneous demand, which is what sizing depends on. Use the load list method instead.

Do I need a generator sized for central air conditioning?

Only if you want AC running during an outage. Central AC has a high starting surge, so it often drives the final size more than anything else.

Should I let the installer size it for me?

Ask for their load calculation in writing and compare it with your own list. For installation scope and costs, check the official details from local dealers, since pricing and requirements vary by region.

Conclusion

Answering whole house generator what size do I need comes down to a clear load list, correct running and starting figures, and a sensible headroom margin. Once you have a kW target, you can compare units with confidence. Have a licensed electrician verify the calculation and handle the electrical connection before you buy.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our generators & noise guides, checking product details against manufacturer specifications and owner feedback.