Updated November 2026
Generator size for whole house backup comes down to one number: the total running watts your home will draw during an outage, plus enough headroom to start the motors that spike the load. This guide walks you through adding up your loads, accounting for starting surges, and landing on a kilowatt rating that keeps the lights, fridge and HVAC running without overloading the unit.
Step 1: List What You Need to Power
Start with the circuits you actually want to keep alive. Most homeowners fall into one of two groups: essential loads only, or nearly the whole house. Essential loads usually include the refrigerator, freezer, furnace blower, sump pump, a few lights, the well pump if you have one, and a router or modem. Whole-home coverage adds central air, the electric range, water heater, dryer and more.
Shopping for one? See our guide: 4 Best Whole House Inverter Generator Options Compared (2026).
Check the nameplate on each appliance. It lists running watts or amps at a given voltage. If it only lists amps, multiply by the voltage (usually 120 V or 240 V) to get watts.
Step 2: Calculate Running and Starting Watts
Running watts are what each device draws continuously. Starting watts are the brief surge a motor needs to spin up. Compressors, well pumps and air conditioners can need two to three times their running load for a second or two. Your generator must handle that surge on top of everything else already running.
- Add the running watts of every load you plan to power at the same time.
- Identify the single largest starting surge. Add that surge value to the running total, minus that motor’s running watts (it is already counted once).
- Add a 20 to 25 percent margin so the generator never runs at its absolute limit.
Step 3: Match the Total to a Generator Rating
Generators are rated in kilowatts (kW) for continuous output, often with a higher surge rating. Use the continuous figure for your sizing decision. Common whole-house sizes fall roughly between 10 kW and 22 kW for air-cooled standby units, with larger units for big homes and multiple HVAC systems. Choose the next size up from your calculated total rather than the nearest one below it.
| Home load profile | Typical sizing direction |
|---|---|
| Essential circuits only, gas furnace, no central AC | Smaller standby unit, often in the lower kW range |
| Essential circuits plus one central AC system | Mid-range unit sized for the AC starting surge |
| Nearly whole house, electric range, multiple AC zones | Upper-range unit, often with a load management plan |
Common Mistakes When Sizing
- Sizing only on running watts and ignoring the compressor surge.
- Assuming the generator’s maximum output is available all the time. Standby ratings are typically tested under specific conditions.
- Forgetting altitude and temperature derating. Output falls at high elevation and in hot weather.
- Planning for today’s loads only and skipping a future addition like an EV charger or a heat pump.
- Estimating appliance loads from memory instead of nameplate data.
Tips for a Safer, Quieter Setup
A correctly sized generator runs cooler, uses less fuel and tends to be quieter because it is not working at its limit. Pair sizing with a load management strategy, such as deferring the dryer or range during an outage. For noise control options, see Whole-House Generator Noise Reduction: 8 Steps That Actually Work. Sizing also determines the transfer hardware you need, so review Whole House Switch for Generator: How to Choose and Install One Safely before finalizing your plan.
If your home has a heat pump or unusual electrical service, have a licensed electrician or generator installer verify the load calculation. A professional can do a formal load analysis that accounts for diversity and your panel configuration.
Recommended Gear
A plug-in load monitor helps you measure real appliance draw before you commit to a size, which is more reliable than guessing from labels. View on Amazon
A clamp-on current meter lets you check the actual amperage on individual circuits in your panel, useful for confirming large-load estimates. View on Amazon
FAQ
How do I know if my generator is big enough for the whole house?
Compare the generator’s continuous kW rating against your calculated running total plus the largest starting surge and a 20 to 25 percent margin. If the generator’s continuous rating covers that total, it is sized correctly.
Is a 22 kW generator enough for a whole house?
It can be, depending on the loads you run at once. Many larger homes with central AC and an electric range fit within that range, but you must still run the calculation for your specific appliances.
Can I size a generator for only essential circuits?
Yes. Sizing for essential circuits usually means a smaller unit and a lower installation scope, and it is a common choice for homeowners who want backup power for the basics. Confirm the plan with a licensed installer.
Conclusion
To size a whole-house generator, add up the running watts of the loads you want during an outage, account for the largest motor surge, and add a safety margin. Then choose the next size up on the continuous kW scale. A licensed installer can verify the numbers against your electrical service before purchase.
